Speedway Dual Feed Brake Master Cylinder, 1 Inch Bore, Disc/Drum

Description

Dual feed master cylinder with 2 bolt flange style mounts, This cylinder is similar to what was used on mid-70's Fords (Mustang, Fairlane/LTD, etc. with disc front/drum rear), 7-1/4" long without the pushrod, add 2" for the pushrod, 3" wide from the outside of the reservoir to the edge of the outlets, Includes 3/8"-24 threaded push rod
Speedway Dual Feed Brake Master Cylinder, 1 Inch Bore, Disc/Drum
Sku # 91031420
Mfr. Part # 91031420
Condition
New
Brand
Speedway Motors
Sold
Each
Details
Notes
Brake System Builder's Tip (Link)
Tech Tip:
The bigger the master cylinder is, the more fluid you get, but you'll have less pressure at the caliper.
There is no longer a loop on the end of the push rod for this master cylinder. It is now threaded 3/8"-24 (fine) male. If you need a yoke for pedal hook-up, use 910-02973.
Info
Dual feed master cylinder with 2 bolt flange style mount. Use with Speedway brake pedal assemblies. This cylinder is similar to those used on mid-70's Fords (Mustang, Fairlane/LTD, etc. with disc front/drum rear).
Works well in disc/disc or disc/drum brake setups
Mounting Bolt Holes: 3/8" or 10mm
7 1/4" long without the pushrod, add 2" for the pushrod
3" wide from the outside of the reservoir to the edge of the outlets
Mounting flange is 4" wide
Master cylinder is also 3-7/16" tall without a cap
Included push rod is threaded 3/8"-24 (fine thread).
If you need a yoke for the pedal hook-up, use this Forged Steel Yoke.
Pushrod boot included.
Uses 3/8"-24 female inverted flare outlets. If plumbing with AN 3 lines, you will need two each of these AN to IFM Adapters.
Learn more about selecting the proper master cylinder for your vehicle by reading our tech article. Brake System Selection.
WARNING: Cancer and Reproductive Harm -- p65Warnings.ca.gov
Specs
Sold in Quantity
Each
Finish
Natural
Outlet Count
Tandem
Reservoir Type
Integral
Notes
Includes 3/8"-24 threaded push rod.
Outlet Fitting
3/8"-24 IFF
Centerline of Holes
3.25
Overall Height
5
Overall Width
4
Reservoir Included
Yes
Brake System Type
Disc/Drum
Position
Firewall
Pushrods Included
Yes
Master Cylinder Material
Steel
Mounted Length
7
MFG. Part #
91031420
Master Cylinder Bore Size
1 Inch
Reviews
Good quality part
Rated
by Ronbo on May 30, 2021
Summary:
Very well made, no issues
Yes, I recommend this product.
I would buy this again
Rated
by Mike on April 05, 2021
Summary:
Still installing. Looks good
Cons:
I have some questions but it's too hard to get
Yes, I recommend this product.
Good upgrade
Rated
by Bobs1937 on December 03, 2020
Summary:
Good to replace a single master cylinder on a frame mount 37 ford brake pedal
Yes, I recommend this product.
should be easy to work on. good quality
Rated
by wayne on August 22, 2020
Summary:
pretty much a standard cylinder-easy to work with!!!!!!!!!!!!!!!
Yes, I recommend this product.
wooks good
Rated
by Cobra on August 10, 2020
Summary:
Replaced a bad master cyc.
Related Items / Suggested Parts
Dual Feed Master Cylinder W/ Internal Stainless Steel Sleeve
Chrome Master Cylinder Cover
Dual Outlet Master Cylinder Steel Dual Brake Line Kit
Replacement Pushrod for Manual Master Cylinder
Shipping
Combined Shipping:
Please take advantage of the “add to cart” button on each listing to get everything in your cart prior to completing checkout. This will ensure you receive a combined shipping rate on your entire order.
Freight Shipping:
Some products are too large for standard ground delivery and must be shipped via truck freight.
Please contact us via eBay Message for a freight shipping estimate.
When possible, please provide a business or commercial address for delivery to eliminate additional fees.
Please ensure the phone number provided is accurate to avoid delays.
Upon delivery, the recipient must inspect the shipment before the driver leaves as there may be concealed damage; please open the carton to inspect the contents. Any visual damage must be noted on the shipping document BEFORE signing for delivery. Any damage not noted before signing for delivery is the buyer’s responsibility. If damage is found, the shipment may be refused, but please contact us as soon as possible and arrangements will be made to have the product replaced and damaged parts returned.
Tech Support
We're here to help before and after your purchase. If you have a question or need assistance with one of our products, please contact us through eBay Messaging and a knowledgeable Speedway Motors team member will be happy to help.
About
Speedway Motors is America’s Oldest Speed Shop® and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 69 years. Founded in 1952 by “Speedy” Bill Smith – a racer and street rodder himself – Speedway has grown from a one-man operation to become the world’s largest manufacturer, distributor and retailer of street rod and racing products. Our industry-leading fast delivery is the result of same-day shipping from our state-of-the-art, centrally located 500,000 sq. ft. headquarters. Speedway’s size offers customers unmatched product selection and low pricing, while our excellent technical support and customer service have made us a recognized leader in the rodding and racing industries.
Return Policy
We want you to be satisfied with your purchase. If within 60 days after you receive your shipment and you are not satisfied, you may return the item for a refund. Refunds will be processed (1-2) days after the item is received by Speedway. All returned merchandise must be in original factory condition with no modifications or alterations. A restocking fee up to 15% may be applied if items are not in new condition.
Returned merchandise must include all packaging materials, warranty cards, manuals, and accessories. If the items being returned need to be repackaged, there will be a repacking charge. Repack the item in a sturdy box, include a copy of your invoice and complete the form on the back of the invoice. You must ship orders back PREPAID. WE DO NOT ACCEPT COD SHIPMENTS.
All fiberglass items returned will be subject to a 15% restocking charge. No returns on electrical parts, DVDs, and books unless they are defective. Absolutely no returns on special order or closeout merchandise.
Payment
Accepted Payment Methods - PayPal and major credit cards are accepted.
Terms - Immediate payment is required on all listings.
To view states in which sales tax will apply to your order, please visit the “shipping and payments” tab.
Guarantee
Speedway accepts full responsibility for the accuracy of our listings and product representation. If an egregious shipping or description error occurs, we are happy to assist with a replacement or refund.
Disclaimer
Due to our large inventory and the diversity of our product line, the stock photo used may not be an exact representation of the item you are bidding on. Please read all product information carefully before purchase to avoid any order issues.